S1000-EWS1000-RWS1000-EBS1000-RBS900-EWS900-RWOWNER’S MANUAL
INSTALLATIONInstallation Parts81. 2 ea Mounting Bolt2. 2 ea Rubber Cone Washer3. 2 ea Flat Washer4. 2 ea Barrel Nut5. Mounting Plate6. 2 ea Adjustable
9Before Installation:Check water supply line:Check the line that connects the toilet tank to the water shut off valve. If it is a rigid pipe, you may n
10a. Install the T-Valve with the rubber washer to the incoming water connection on the bottom of your toilet tank. Be sure that you place the flat ed
118. Connect Powera. Plug the power cord into the electrical outlet.Important: Make sure to only use a grounded GFI (ground fault interrupter) electri
12OPERATIONQuick Reference Guide: Bidet SeatNote: Basic functions such as Rear Cleansingand Nozzle Cleaning can be used without theremote by utilizing
13OPERATIONQuick Reference Guide: Remote ControlSpray‘Wide Spray’ buttonACDBFor the Swash 900 models the Move, Dry, Sterilize, and Deodorize functions
14OPERATIONQuick Reference Guide: Remote Control (Page 2)ABDCWhen the “Wide Spray” button is pressed,the indicator cycles through the following optio
15OPERATIONUsing the SwashImportant note: The wash functions and the warm air dryer function will not work unless the body sensor in the seat detects
16OPERATIONWater Flow / Water Pressure AdjustmentWhile the cleansing function is operating, press the Water Pressure/Dry Temp “+” and “-“ buttons on t
17OPERATIONWarm Air Dryer Temperature – Swash 1000 OnlyWhile air dryer function is operating, press the Water Pressure/Dry Temp. button “+” and “-“ to
TABLE OF CONTENTSThis manual contains important safety information. Before operating theunit, please read this manual thoroughly, and retain it for fu
18OPERATION(If no buttons on the Remote control are pressed for approximately 5 seconds, the remote display lights are turned off to conserve remote ba
19SPECIFICATIONSBrondell SwashS1000-EW, S1000-RW, S1000-EB, 1000-RB, S900-EW, S900-RWRemote control dimensionsRemote: 2”(Width) x 5” (Length) x 1” (D
20MAINTENANCESeat Cleaning and RemovalImportant: Unplug the Swash from the power source before cleaning or removing the seat.Use a soft, damp cloth an
21MAINTENANCETROUBLESHOOTINGProduct Storage & UseShort term non-use: If the product will not be used for more than a few weeks, you can simply unp
22TROUBLESHOOTINGProblem Possible CausesPossible Solutions1. Bidet not plugged in2. No power to Swash3. There is power, but nothing happens when tryin
23TROUBLESHOOTINGProblem Possible CausesPossible Solutions1. Seat temperature set to off2. Resettable fuse blownSeat not heated 1. Make sure that the S
24Brondell Warranty PolicyBrondell products are backed by some of the most comprehensive warranties in the industry. Brondell warrants that all produc
25d) Damage or loss resulting from negligent or improper installation including installation of a unit in a harsh or hazardous environment.e) Damage o
26Brondell, Inc.PO Box 470085San Francisco, CA 94147-0085Phone: 1-888-542-3355Email: [email protected]: www.brondell.comFor detailed warranty in
PRODUCT FEATURESSwash 900 and Swash 1000 Models:Ergonomic heated seat – with four temperature settings (High/Med/Low/Off).Instant and endless warm wate
SAFETY PRECAUTIONSDanger: If not observed, serious injury or even death may occur as a result of electrocution.Warning: If these warnings are not obse
3• If foreign material enters the product, pull the power plug out of the electrical outlet, turn off the main water valve, and call the Brondell Servi
4• Do not open/close the seat cover using excessive force. • Exercise caution that urine does not come into contact with the nozzles or warm air dryer
PARTS & CONFIGURATIONThe Swash 900 and the Swash 1000 have the following dimensions:5411 mm(16.2 inch)382 mm(15 inch)202 mm(7.9 inch)350 mm(13.8
PARTS & CONFIGURATIONProduct Configuration1. Lid2. Warning sticker3. IR sensor4. Nozzles5. Body (seat) sensor6. Bidet seat7. Bidet hose8. T-valve c
REMOTE CONTROL7Swash 900 Swash 1000SpraySpray
Commentaires sur ces manuels